High efficiency synthesis of Nd:YAG powder by a spray co-precipitation method for transparent ceramics

A spray co-precipitation method was developed to efficiently synthesize Nd:YAG nano-powders. The effects of spray speeds and solution concentrations on the crystallization processes of calcined precursors have been studied. The results indicated that the pure phase of YAG could be obtained by three different crystallization processes owing to different homogeneity levels of Y and Al mixing. Pure YAG powder was obtained at 850?°C and the phase purity persisted to 1600?°C. Using the obtained powders, transparent ceramics with the in-line transmittance up to 80.2%@400 nm and 83.1%@1064?nm were fabricated by gel-casting method and hot isostatic pressing sintering. Furthermore, the microstructure and laser properties of the transparent ceramics have been measured. The maximum laser output of 7.015?W has been obtained with an oscillation threshold and a slope efficiency of 0.235?W and 59.4%, respectively.     

La0.6Sr0.4Co0.2Fe0.8O3-δ nanofiber cathode for intermediate-temperature solid oxide fuel cells by water-based sol-gel electrospinning: Synthesis and electrochemical behaviour

Water-based sol-gel electrospinning is employed to manufacture perovskite oxide La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF) nanofiber cathodes for intermediate-temperature solid oxide fuel cells. LSCF fibrous scaffolds are synthesized through electrospinning of a sol-gel solution employing water as the only solvent. Morphological characterizations demonstrate that the LSCF fibers have highly crystalline structure with uniform elemental distribution. After heat treatment, the average fiber diameter is 250 nm and the porosity of the nanofiber tissue is 37.5 %. The heat treated LSCF nanofibers are applied directly onto a Ce_0.9Gd_0.1O_1.95 (CGO) electrolyte disk to form a symmetrical cell. Electrochemical characterization is carried out through electrochemical impedance spectroscopy (EIS) in the temperature range 550?°C–950?°C, and reproducibility of the electrochemical performance for a series of cells is demonstrated. At 650?°C, the average measured polarization resistance R_p is 1.0 Ω cm². Measured performance decay is 1 % during the first 33?h of operation at 750?°C, followed by an additional 0.7 % over the subsequent 70?h.     

Effects of anion and cation doping on the thermoelectric properties of n-type PbS

The PbCl_xS_1-x and Pb_1-xBi_xS (x? =?0–0.05) bulks were fabricated with a facile method of hydrothermal synthesis and microwave sintering, and the effect of anionic and cationic donors on the thermoelectric performance of PbS was investigated. Although Cl^? and Bi³⁺ both effectively improved the thermoelectric properties of n-type PbS, more excellent thermoelectric performance was obtained from Cl^? doped samples because of higher electrical property and lower thermal conductivity at higher temperature (T? >?600?K). The thermoelectric figure of merit (ZT) reaches 1.04 for PbCl_0.015S_0.985 at 800?K and increases with temperature increasing without sign of saturation, which is probably the highest value ever reported for single-phase polycrystalline n-type PbS. The results also indicate that the hydrothermal synthesis and microwave sintering can realize anion doping as well as cation doping for n-type PbS at low cost, and PbS should be a robust alternative for PbTe thermoelectric materials.     

Microwave-assisted solution synthesis,microwave sintering and magnetic properties of cobalt ferrite

A simple, soft, and fast microwave-assisted hydrothermal method was used for the preparation of nanocrystalline cobalt ferrite powders from commercially-available Fe(NO₃)₃?9H₂O, Co(NO₃)₂?6H₂O, ammonium hydroxide, and tetrapropylammonium hydroxide (TPAH). The synthesis was conducted in a sealed-vessel microwave reactor specifically designed for synthetic applications, and the resulting products were characterized by XRD, FE-SEM, TEM, and HR-TEM. After a systematic study of the influence of the microwave variables (temperature, reaction time and nature of the bases), highly crystalline CoFe₂O₄ nanoparticles with a high uniformity in morphology and size, were directly obtained by heating at 130?°C for 20?min using the base TPAH. Dense ceramics of cobalt ferrite were prepared by non-conventional, microwave sintering of synthesized nanopowders at temperatures of 850–900?°C. The magnetic properties of both the nanopowders and the sintered specimens were determined in order to establish their feasibility as a permanent magnet.     

Oxoisoaporphine Alkaloids: Prospective Anti‐Alzheimer's Disease,Anticancer, and Antidepressant Agents

Oxoisoaporphine alkaloids are a family of oxoisoquinoline‐derived alkaloids that were first isolated from the rhizome of Menispermum dauricum DC. (Menispermaceae). It has been demonstrated that oxoisoaporphine alkaloids possess various biological properties, such as cholinesterase and β‐amyloid inhibition, acting as a topoisomerase intercalator, monoamine oxidase A inhibition, and are expected to become anti‐Alzheimer's disease, anticancer, and antidepressant drugs. This review provides an overview of natural sources, synthetic routes, bioactivities, structure–function relationship, and modification investigations into oxoisoaporphine alkaloids, with the aim of providing references to the structure–activity relationships for the design and development of oxoisoaporphine derivatives with higher efficacy and therapeutic potential.     

基于局部放电法的矿用高压电缆信号去噪算法研究

干扰噪声直接影响局部放电法有效检测矿用高压电缆故障。基于局部放电法，综合采用理论计算、仿真实验、现场试验的方法，对比分析了短时傅里叶变换和傅里叶分析去噪法的原理和优缺点，提出了一种矿用高压电缆的局部放电去噪算法——小波阈值去噪法，同时，选择了合理的阈值函数和去噪流程。基于此，采用白噪声和连续周期信号作为高压电缆的干扰噪声，进行了模拟仿真实验。结果表明，小波阈值去噪法可有效抑制白噪声，其中，Db2小波性能和去噪效果最好；同时，现场试验结果显示，去噪后信噪比得到了显著增加，验证了小波阈值去噪法的合理性和可靠性。     

Solution combustion synthesis of cerium oxide nanoparticles as corrosion inhibitor

In this study, combustion synthesis of cerium oxide nanoparticles was reported using cerium nitrate hexahydrate as starting material as well as urea, glycine, glucose, and citric acid as fuels. The influence of fuel type on structure, microstructure, band gap, and corrosion inhibition was investigated. X-ray diffraction (XRD) patterns and scanning electron microscopy micrographs showed that CeO₂ nanoparticles with different morphologies were obtained depending on the fuel type. Microstructural changes from unreacted gel to sponge-like morphologies were resulted by varying the fuel type from urea, glycine, and glucose to citric acid. In addition to Ce–O bonds, Fourier transform infrared analysis showed carbon bonds of carbonaceous compositions from incomplete combustion which were declined during combustion reaction. Furthermore, corrosion analyses showed that samples synthesized using urea fuel released the most Ce⁺⁴ ions and could have better protection than other samples.     

Modification of structure and conductivity of nanohorns by toluene addition in carbon arc

Abstract

In the present work, we compare the structure and transport properties of carbon nanohorns (CNHs) synthesized by arc evaporation of graphite alone and with the addition of some portion of toluene. The materials have been investigated using transmission electron microscopy, Raman and infrared spectroscopies, thermogravimetric and BET analyses. The addition of a small amount of toluene during the evaporation of graphitic rod increases the length of CNHs, affects their hierarchical arrangement in aggregates and results in surface functionalization. All these features significantly enhance the conductivity of CNHs obtained with toluene additive in comparison with the pristine CNHs.     

A Mobile Cloud-Based eHealth Scheme

Mobile cloud computing is an emerging field that is gaining popularity across borders at a rapid pace. Similarly, the field of health informatics is also considered as an extremely important field. This work observes the collaboration between these two fields to solve the traditional problem of extracting Electrocardiogram signals from trace reports and then performing analysis. The developed system has two front ends, the first dedicated for the user to perform the photographing of the trace report. Once the photographing is complete, mobile computing is used to extract the signal. Once the signal is extracted, it is uploaded into the server and further analysis is performed on the signal in the cloud. Once this is done, the second interface, intended for the use of the physician, can download and view the trace from the cloud. The data is securely held using a password-based authentication method. The system presented here is one of the first attempts at delivering the total solution, and after further upgrades, it will be possible to deploy the system in a commercial setting.